2022-06-20 06:20:56 +02:00
|
|
|
// Copyright 2018-2022 Nick Brassel (@tzarc)
|
|
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
|
#pragma once
|
|
|
|
|
|
|
|
|
|
// Limit the backlight brightness
|
|
|
|
|
#ifndef BACKLIGHT_LIMIT_VAL
|
|
|
|
|
# define BACKLIGHT_LIMIT_VAL 144
|
|
|
|
|
#endif // BACKLIGHT_LIMIT_VAL
|
|
|
|
|
|
|
|
|
|
// Split configuration
|
|
|
|
|
#define SPLIT_HAND_PIN B9
|
|
|
|
|
#define USB_VBUS_PIN B12
|
|
|
|
|
#define SERIAL_USART_DRIVER SD3
|
|
|
|
|
#define SERIAL_USART_PIN_SWAP
|
|
|
|
|
#define SERIAL_USART_TX_PIN B10
|
|
|
|
|
#define SERIAL_USART_TX_PAL_MODE 7
|
|
|
|
|
#define SERIAL_USART_RX_PIN B11
|
|
|
|
|
#define SERIAL_USART_RX_PAL_MODE 7
|
|
|
|
|
#ifndef SERIAL_USART_SPEED
|
|
|
|
|
# define SERIAL_USART_SPEED 1200000
|
|
|
|
|
#endif // SERIAL_USART_SPEED
|
|
|
|
|
#define SERIAL_USART_FULL_DUPLEX
|
|
|
|
|
|
|
|
|
|
// RGB configuration
|
|
|
|
|
#define RGBLED_NUM 86
|
2022-09-23 14:46:23 +02:00
|
|
|
#define RGB_MATRIX_LED_COUNT 86
|
2022-06-20 06:20:56 +02:00
|
|
|
#define RGB_MATRIX_SPLIT \
|
|
|
|
|
{ 43, 43 }
|
|
|
|
|
#define RGB_POWER_ENABLE_PIN B0
|
|
|
|
|
#define RGB_CURR_1500mA_OK_PIN C5
|
|
|
|
|
#define RGB_CURR_3000mA_OK_PIN C4
|
|
|
|
|
|
|
|
|
|
// EEPROM configuration
|
|
|
|
|
#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN B5
|
|
|
|
|
#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR 8 // (160MHz/8) => 20MHz
|
|
|
|
|
#define EXTERNAL_EEPROM_BYTE_COUNT 8192
|
|
|
|
|
#define EXTERNAL_EEPROM_PAGE_SIZE 64 // it's FRAM, so it doesn't actually matter, this just sets the RAM buffer size
|
|
|
|
|
|
|
|
|
|
// External flash config
|
|
|
|
|
#define EXTERNAL_FLASH_SPI_MODE 3
|
|
|
|
|
#define EXTERNAL_FLASH_SPI_SLAVE_SELECT_PIN A8
|
|
|
|
|
#define EXTERNAL_FLASH_SPI_CLOCK_DIVISOR 4 // (160MHz/4) => 40MHz
|
|
|
|
|
#define EXTERNAL_FLASH_SIZE (4 * 1024 * 1024) // 32Mb/4MB capacity
|
|
|
|
|
|
|
|
|
|
// Fault indicators
|
|
|
|
|
#define BOARD_POWER_FAULT_PIN C9
|
|
|
|
|
#define RGB_POWER_FAULT_PIN C4
|
