Merge remote-tracking branch 'origin/master' into develop

This commit is contained in:
QMK Bot 2021-06-02 23:48:58 +00:00
commit 65fe74fde0
19 changed files with 61 additions and 11 deletions

View File

@ -72,7 +72,9 @@ WS2812_DRIVER = spi
Configure the hardware via your config.h:
```c
#define WS2812_SPI SPID1 // default: SPID1
#define WS2812_SPI_MOSI_PAL_MODE 5 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
#define WS2812_SPI_MOSI_PAL_MODE 5 // MOSI pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
#define WS2812_SPI_SCK_PIN B3 // Required for F072, may be for others -- SCK pin, see the respective datasheet for the appropriate values for your MCU. default: unspecified
#define WS2812_SPI_SCK_PAL_MODE 5 // SCK pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
```
You must also turn on the SPI feature in your halconf.h and mcuconf.h
@ -100,11 +102,11 @@ Only divisors of 2, 4, 8, 16, 32, 64, 128 and 256 are supported by hardware.
While not an exhaustive list, the following table provides the scenarios that have been partially validated:
| | SPI1 | SPI2 | SPI3 |
|-|-|-|-|
| f072 | ? | B15 :heavy_check_mark: | N/A |
| f103 | A7 :heavy_check_mark: | B15 :heavy_check_mark: | N/A |
| f303 | A7 :heavy_check_mark: B5 :heavy_check_mark: | B15 :heavy_check_mark: | B5 :heavy_check_mark: |
| | SPI1 | SPI2 | SPI3 |
|------|---------------------------------------------|-----------------------------------------|-----------------------|
| f072 | ? | B15 :heavy_check_mark: (needs SCK: B13) | N/A |
| f103 | A7 :heavy_check_mark: | B15 :heavy_check_mark: | N/A |
| f303 | A7 :heavy_check_mark: B5 :heavy_check_mark: | B15 :heavy_check_mark: | B5 :heavy_check_mark: |
*Other supported ChibiOS boards and/or pins may function, it will be highly chip and configuration dependent.*

View File

@ -16,19 +16,23 @@
# define WS2812_SPI_MOSI_PAL_MODE 5
#endif
#ifndef WS2812_SPI_SCK_PAL_MODE
# define WS2812_SPI_SCK_PAL_MODE 5
#endif
// Push Pull or Open Drain Configuration
// Default Push Pull
#ifndef WS2812_EXTERNAL_PULLUP
# if defined(USE_GPIOV1)
# define WS2812_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
# define WS2812_MOSI_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
# else
# define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL
# define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL
# endif
#else
# if defined(USE_GPIOV1)
# define WS2812_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_OPENDRAIN
# define WS2812_MOSI_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_OPENDRAIN
# else
# define WS2812_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN
# define WS2812_MOSI_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_MOSI_PAL_MODE) | PAL_STM32_OTYPE_OPENDRAIN
# endif
#endif
@ -63,6 +67,12 @@
# define WS2812_SPI_BUFFER_MODE 0 // normal buffer
#endif
#if defined(USE_GPIOV1)
# define WS2812_SCK_OUTPUT_MODE PAL_MODE_STM32_ALTERNATE_PUSHPULL
#else
# define WS2812_SCK_OUTPUT_MODE PAL_MODE_ALTERNATE(WS2812_SPI_SCK_PAL_MODE) | PAL_STM32_OTYPE_PUSHPULL
#endif
#define BYTES_FOR_LED_BYTE 4
#define NB_COLORS 3
#define BYTES_FOR_LED (BYTES_FOR_LED_BYTE * NB_COLORS)
@ -109,7 +119,11 @@ static void set_led_color_rgb(LED_TYPE color, int pos) {
}
void ws2812_init(void) {
palSetLineMode(RGB_DI_PIN, WS2812_OUTPUT_MODE);
palSetLineMode(RGB_DI_PIN, WS2812_MOSI_OUTPUT_MODE);
#ifdef WS2812_SPI_SCK_PIN
palSetLineMode(WS2812_SPI_SCK_PIN, WS2812_SCK_OUTPUT_MODE);
#endif // WS2812_SPI_SCK_PIN
// TODO: more dynamic baudrate
static const SPIConfig spicfg = {WS2812_SPI_BUFFER_MODE, NULL, PAL_PORT(RGB_DI_PIN), PAL_PAD(RGB_DI_PIN), WS2812_SPI_DIVISOR};

View File

@ -51,6 +51,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
//SPI
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
#define WS2812_EXTERNAL_PULLUP
// I2C OLED defines

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 14
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*
* Feature disable options

View File

@ -50,6 +50,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGB_DI_PIN B15
#define RGBLED_NUM 22
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*
* Feature disable options

View File

@ -55,6 +55,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGB_DI_PIN B15
#define RGBLED_NUM 20
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*
* Feature disable options

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 20
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*
* Feature disable options

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 14
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*
* Feature disable options

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 20
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 20
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*

View File

@ -60,6 +60,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 8
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
#define DYNAMIC_KEYMAP_LAYER_COUNT 2

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 20
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 22
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*
* Feature disable options

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 20
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/*

View File

@ -100,6 +100,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define WS2812_SPI SPID2 // default: SPID1
#define WS2812_SPI_MOSI_PAL_MODE 0 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
#define RGB_DI_PIN B15
#ifdef RGB_DI_PIN

View File

@ -36,6 +36,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 3
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
/* Set 0 if debouncing isn't needed */
#define DEBOUNCE 5

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 14
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
#define INDICATOR_PIN_0 A0
#define INDICATOR_PIN_1 A1

View File

@ -56,6 +56,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define RGBLED_NUM 14
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
#define INDICATOR_PIN_0 A9
#define INDICATOR_PIN_1 A8

View File

@ -67,6 +67,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
// SPI RGB Driver
#define WS2812_SPI SPID2
#define WS2812_SPI_MOSI_PAL_MODE 0
#define WS2812_SPI_SCK_PAL_MODE 0
#define WS2812_SPI_SCK_PIN B13
// OLED defines
#define OLED_TIMEOUT 60000