153 lines
4.5 KiB
Makefile
153 lines
4.5 KiB
Makefile
#----------------------------------------------------------------------------
|
|
# On command line:
|
|
#
|
|
# make all = Make software.
|
|
#
|
|
# make clean = Clean out built project files.
|
|
#
|
|
# make coff = Convert ELF to AVR COFF.
|
|
#
|
|
# make extcoff = Convert ELF to AVR Extended COFF.
|
|
#
|
|
# make program = Download the hex file to the device.
|
|
# Please customize your programmer settings(PROGRAM_CMD)
|
|
#
|
|
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
|
# (must have teensy_loader_cli installed).
|
|
#
|
|
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
|
# have dfu-programmer installed).
|
|
#
|
|
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
|
# have Atmel FLIP installed).
|
|
#
|
|
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
|
# (must have dfu-programmer installed).
|
|
#
|
|
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
|
# (must have Atmel FLIP installed).
|
|
#
|
|
# make debug = Start either simulavr or avarice as specified for debugging,
|
|
# with avr-gdb or avr-insight as the front end for debugging.
|
|
#
|
|
# make filename.s = Just compile filename.c into the assembler code only.
|
|
#
|
|
# make filename.i = Create a preprocessed source file for use in submitting
|
|
# bug reports to the GCC project.
|
|
#
|
|
# To rebuild project do "make clean" then "make all".
|
|
#----------------------------------------------------------------------------
|
|
|
|
# Target file name (without extension).
|
|
# TARGET ?= usb_usb
|
|
|
|
# TMK_DIR ?= ../../tmk_core
|
|
|
|
# Directory keyboard dependent files exist
|
|
# TARGET_DIR ?= .
|
|
|
|
# MCU name
|
|
MCU ?= atmega32u4
|
|
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU ?= 8000000
|
|
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH ?= AVR8
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB ?= $(F_CPU)
|
|
# Interrupt driven control endpoint task
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
#MOUSEKEY_ENABLE ?= yes # Mouse keys
|
|
EXTRAKEY_ENABLE ?= yes # Media control and System control
|
|
# CONSOLE_ENABLE ?= yes # Console for debug
|
|
CONSOLE_ENABLE ?= no # Console for debug
|
|
#COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
|
#NKRO_ENABLE ?= yes # USB Nkey Rollover
|
|
|
|
# Boot Section Size in bytes
|
|
# Teensy halfKay 512
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
#LDFLAGS += -Wl,--relax
|
|
|
|
#OPT_DEFS += -DNO_ACTION_TAPPING
|
|
#OPT_DEFS += -DNO_ACTION_LAYER
|
|
#OPT_DEFS += -DNO_ACTION_MACRO
|
|
|
|
CUSTOM_MATRIX = yes
|
|
|
|
SRC = matrix.cpp
|
|
|
|
#
|
|
# Keymap file
|
|
#
|
|
# ifeq (yes,$(strip $(UNIMAP_ENABLE)))
|
|
# KEYMAP_FILE = unimap
|
|
# else
|
|
# ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
|
|
# KEYMAP_FILE = actionmap
|
|
# else
|
|
# KEYMAP_FILE = keymap
|
|
# endif
|
|
# endif
|
|
# ifdef KEYMAP
|
|
# SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
|
|
# else
|
|
# SRC := $(KEYMAP_FILE).c $(SRC)
|
|
# endif
|
|
|
|
# CONFIG_H ?= config.h
|
|
|
|
|
|
|
|
# Search Path
|
|
# VPATH += $(TARGET_DIR)
|
|
# VPATH += $(TMK_DIR)
|
|
|
|
|
|
|
|
# program Leonardo
|
|
# PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -b57600 -Uflash:w:$(TARGET).hex -P$(DEV)
|
|
|
|
|
|
|
|
# include $(TMK_DIR)/protocol/usb_hid.mk
|
|
# include $(TMK_DIR)/protocol/lufa.mk
|
|
# include $(TMK_DIR)/common.mk
|
|
# include $(TMK_DIR)/rules.mk
|