ebb512db82
* Clean up `DEBOUNCE` in config.h, 0-9 * Clean up `DEBOUNCE` in config.h, A * Clean up `DEBOUNCE` in config.h, B * Clean up `DEBOUNCE` in config.h, C * Clean up `DEBOUNCE` in config.h, D * Clean up `DEBOUNCE` in config.h, E * Clean up `DEBOUNCE` in config.h, F * Clean up `DEBOUNCE` in config.h, G * Clean up `DEBOUNCE` in config.h, H * Clean up `DEBOUNCE` in config.h, handwired * Clean up `DEBOUNCE` in config.h, I * Clean up `DEBOUNCE` in config.h, J * Clean up `DEBOUNCE` in config.h, K * Clean up `DEBOUNCE` in config.h, L * Clean up `DEBOUNCE` in config.h, M * Clean up `DEBOUNCE` in config.h, N * Clean up `DEBOUNCE` in config.h, O * Clean up `DEBOUNCE` in config.h, P * Clean up `DEBOUNCE` in config.h, Q * Clean up `DEBOUNCE` in config.h, R * Clean up `DEBOUNCE` in config.h, S * Clean up `DEBOUNCE` in config.h, T * Clean up `DEBOUNCE` in config.h, U * Clean up `DEBOUNCE` in config.h, V * Clean up `DEBOUNCE` in config.h, W * Clean up `DEBOUNCE` in config.h, X * Clean up `DEBOUNCE` in config.h, Y * Clean up `DEBOUNCE` in config.h, Z * Remove default debounce from info.json * Migrate non-default debounce to info.json |
||
---|---|---|
.. | ||
keymaps | ||
stm32f103 | ||
t2pp | ||
config.h | ||
info.json | ||
readme.md | ||
rules.mk | ||
sono1.c | ||
sono1.h |
readme.md
QMK-based firmware for ASkeyboard Sono1 keyboard with additional Sono2 numpad
ASkeyboard Sono1 keyboard conversion project: direct connection of Black Pill to the matrix.
- Keyboard Maintainer: DmNosachev
- Hardware Supported: ASkeyboard Sono1, Teensy 2.0++ or Black Pill STM32F103C8T6 MCU board. Alternatively you can use any MCU which is supported by QMK and has 28 IO pins or more (15x8 matrix and 5 LEDs): Blue Pill, Black Pill STM32F4xx, etc.
Make example for this keyboard (after setting up your build environment):
qmk compile -kb handwired/sono1:default
See the build environment setup and the make instructions for more information. Brand new to QMK? Start with our Complete Newbs Guide.
Modding
Matrix
ASkeyboard Sono1 has 15x8 matrix. Sono2 numpad connects directly to the main matrix.
Rows (R0-RE) and columns (R0-C7):
Desolder all ICs, capacitors and resistors except R10–R14.
LEDs
Keyboard has 5 LEDs with common anode. Their cathodes are connected to R10–R14 resistors (you may want to replace them to adjust LED brightness for 3.3V voltage). Add 5 wire jumpers to connect them to the corresponding traces.
Teensy 2.0++
Suggested mount position for the Teensy 2.0++ (view from the bottom side of the PCB):
R8 R9 RA RB RC RD RE L0 R8 C7 C6 C5 C4 C3 C2 C1 C0
* | | | | | | | * | | | | | | | |
,------------------------------------------------------------,
,---|GN B7 D0 D1 D2 D3 D4 D5 D6 D7 E0 E1 C0 C1 C2 C3 C4 C5 C6 C7 |
| |D7 |
|USB| |
| |GN |
'---|V B6 B5 B4 B3 B2 B1 B0 E7 E6 G A F0 F1 F2 F3 F4 F5 F6 F7 |
`------------------------------------------------------------'
* | | | | | | | | | | | |
GN L2 L1 L3 L4 R7 R6 R5 R4 R3 R2 R1 R0
Asterisk sign designates pins of the Teensy that don't align properly with PCB and need to be rewired.
- Compile and flash the firmware:
qmk compile -kb handwired/sono1/t2pp:default:flash
. Press the reset button on Teensy to launch the bootloader. - You will need to solder several pin headers to Teensy: two 7 pin headers (C0–C7, D5–B7), 8 pin (F0–F7) and 4 pin (B1—B4).
- Solder the Teensy to keyboard's PCB. You will need to manually reroute only 3 pins.
Black Pill
Suggested mount position for the Black Pill (view from the bottom side of the PCB):
R8 R9 RA RB RC RD RE L0 Vcc C7 C6 C5 C4 C3 C2 C1 C0 Vcc
* | | | * | | | | | | | | | * * *
,------------------------------------------------------------------------,
,---|GND B8 B9 C13 RST A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B10 B11 3V3| A3 A4 3V3
| | B7 A15 A13|
|USB| A14|
| | B12 A10 GND|
'---|GND 3V3 B7 B6 B5 B4 B3 A15 A12 A11 A10 A9 A8 B15 B14 B13 B12 |
'------------------------------------------------------------------------' A9 B3 A5
| | | | * | | | | * * * *
GND L2 L1 L3 L4 R7 R6 R5 R4 R3 R2 R1 R0
Asterisk sign designates pins of the Black Pill that don't align properly with PCB and need to be rewired.
- Solder 4-pin SWD header to Black Pill.
- Burn STM32duino bootloader to Black Pill.
- Compile and flash the firmware:
qmk compile -kb handwired/sono1/stm32f103:default:flash
- Connect rows, columns and LED pads to the corresponding pins of the Black Pill.
Keymap
'CUR LOCK' key on Sono2 numpad has locking switch by default (Alps SKCL lock). QMK supports mechanical locking switches for CapsLock, NumLock and ScrollLock keycodes.
There is 'debug' keymap which doesn't output any scancodes, but displays row and column numbers of pressed buttons to console (hid_listen or QMK Toolbox).