qmk_firmware/Key-Functions.md

Quick Aliases To Common Actions

Your keymap can include shortcuts to common operations (called "function actions" in tmk).

These functions work the same way that their ACTION_* functions do - they're just quick aliases. To dig into all of the tmk ACTION_* functions, please see the TMK documentation.

Instead of using FNx when defining ACTION_* functions, you can use F(x) - the benefit here is being able to use more than 32 function actions (up to 4096), if you happen to need them.

Switching and toggling layers

MO(layer) - momentary switch to layer. As soon as you let go of the key, the layer is deactivated and you pop back out to the previous layer. When you apply this to a key, that same key must be set as KC_TRNS on the destination layer. Otherwise, you won't make it back to the original layer when you release the key (and you'll get a keycode sent). You can only switch to layers above your current layer. If you're on layer 0 and you use MO(1), that will switch to layer 1 just fine. But if you include MO(3) on layer 5, that won't do anything for you -- because layer 3 is lower than layer 5 on the stack.

OSL(layer) - momentary switch to layer, as a one-shot operation. So if you have a key that's defined as OSL(1), and you tap that key, then only the very next keystroke would come from layer 1. You would drop back to layer zero immediately after that one keystroke. That's handy if you have a layer full of custom shortcuts -- for example, a dedicated key for closing a window. So you tap your one-shot layer mod, then tap that magic 'close window' key, and keep typing like a boss. Layer 1 would remain active as long as you hold that key down, too (so you can use it like a momentary toggle-layer key with extra powers).

LT(layer, kc) - momentary switch to layer when held, and kc when tapped. Like MO(), this only works upwards in the layer stack (layer must be higher than the current layer).

TG(layer) - toggles a layer on or off. As with MO(), you should set this key as KC_TRNS in the destination layer so that tapping it again actually toggles back to the original layer. Only works upwards in the layer stack.

TO(layer) - Goes to a layer. This code is special, because it lets you go either up or down the stack -- just goes directly to the layer you want. So while other codes only let you go up the stack (from layer 0 to layer 3, for example), TO(2) is going to get you to layer 2, no matter where you activate it from -- even if you're currently on layer 5. This gets activated on keydown (as soon as the key is pressed).

TT(layer) - Layer Tap-Toggle. If you hold the key down, the layer becomes active, and then deactivates when you let go. And if you tap it, the layer simply becomes active (toggles on).

Fun with modifier keys

• LSFT(kc) - applies left Shift to kc (keycode) - S(kc) is an alias
• RSFT(kc) - applies right Shift to kc
• LCTL(kc) - applies left Control to kc
• RCTL(kc) - applies right Control to kc
• LALT(kc) - applies left Alt to kc
• RALT(kc) - applies right Alt to kc
• LGUI(kc) - applies left GUI (command/win) to kc
• RGUI(kc) - applies right GUI (command/win) to kc
• HYPR(kc) - applies Hyper (all modifiers) to kc
• MEH(kc) - applies Meh (all modifiers except Win/Cmd) to kc
• LCAG(kc) - applies CtrlAltGui to kc

You can also chain these, like this:

LALT(LCTL(KC_DEL)) -- this makes a key that sends Alt, Control, and Delete in a single keypress.

The following shortcuts automatically add LSFT() to keycodes to get commonly used symbols. Their long names are also available and documented in quantum/quantum_keycodes.h.

KC_TILD  ~
KC_EXLM  !
KC_QUES  ?
KC_AT    @
KC_HASH  #
KC_DLR   $
KC_PERC  %
KC_CIRC  ^
KC_AMPR  &
KC_ASTR  *
KC_LPRN  (
KC_RPRN  )
KC_UNDS  _
KC_PLUS  +
KC_DQUO  "
KC_LCBR  {
KC_RCBR  }
KC_LABK  <
KC_RABK  >
KC_PIPE  |
KC_COLN  :

OSM(mod) - this is a "one shot" modifier. So let's say you have your left Shift key defined as OSM(MOD_LSFT). Tap it, let go, and Shift is "on" -- but only for the next character you'll type. So to write "The", you don't need to hold down Shift -- you tap it, tap t, and move on with life. And if you hold down the left Shift key, it just works as a left Shift key, as you would expect (so you could type THE). There's also a magical, secret way to "lock" a modifier by tapping it multiple times. If you want to learn more about that, open an issue. :)

MT(mod, kc) - is mod (modifier key - MOD_LCTL, MOD_LSFT) when held, and kc when tapped. In other words, you can have a key that sends Esc (or the letter O or whatever) when you tap it, but works as a Control key or a Shift key when you hold it down.

These are the values you can use for the mod in MT() and OSM():

• MOD_LCTL
• MOD_LSFT
• MOD_LALT
• MOD_LGUI
• MOD_RCTL
• MOD_RSFT
• MOD_RALT
• MOD_RGUI
• MOD_HYPR
• MOD_MEH

These can also be combined like MOD_LCTL | MOD_LSFT e.g. MT(MOD_LCTL | MOD_LSFT, KC_ESC) which would activate Control and Shift when held, and send Escape when tapped. Note however, that you cannot mix right and left side modifiers.

We've added shortcuts to make common modifier/tap (mod-tap) mappings more compact:

• CTL_T(kc) - is LCTL when held and kc when tapped
• SFT_T(kc) - is LSFT when held and kc when tapped
• ALT_T(kc) - is LALT when held and kc when tapped
• GUI_T(kc) - is LGUI when held and kc when tapped
• ALL_T(kc) - is Hyper (all mods) when held and kc when tapped. To read more about what you can do with a Hyper key, see this blog post by Brett Terpstra
• LCAG_T(kc) - is CtrlAltGui when held and kc when tapped
• MEH_T(kc) - is like Hyper, but not as cool -- does not include the Cmd/Win key, so just sends Alt+Ctrl+Shift.