* Fix overflow in WPM calculations.
First, the "fresh" WPM calculation could end up being up to 12000 (with
default `WPM_ESTIMATED_WORD_SIZE`) if keys were pressed more or less
simultaneously. This value has now been clamped down to 255, in effect
clamping WPM to its max value of 255.
Second, with `WPM_ALLOW_COUNT_REGRESSION` enabled, it was possible to
regress the WPM below 0 (i.e. to 255) by just repeatedly pressing
backspace.
* Fix WPM being limited to 235 due to float/int logic.
This takes up about 700 bytes of space, and needs to be swapped to
opt-in, rather than opt-out. Build failures in general on AVR due to the
scarcity of available flash. People can re-enable it by adding to their
keymap's config.h files:
```
#define RGBLIGHT_EFFECT_TWINKLE
```
The prototype of matrix_output_unselect_delay() has been changed as follows.
```c
void matrix_output_unselect_delay(uint8_t line, bool key_pressed);
```
Currently, no keyboard seems to be redefining `matrix_output_unselect_delay()`, so there is no change in the system behavior.
With this change, the keyboard level code can get some optimization hints, for example, the following.
```c
void matrix_output_unselect_delay(uint8_t line, bool key_pressed) {
/* If none of the keys are pressed,
* there is no need to wait for time for the next line. */
if (key_pressed) {
#ifdef MATRIX_IO_DELAY
# if MATRIX_IO_DELAY > 0
wait_us(MATRIX_IO_DELAY);
# endif
#else
wait_us(30);
#endif
}
}
```
Two occurrences of `MATRIX_ROWS` weren't properly changed to
`ROWS_PER_HAND` in #13330, causing a crash during boot on at least my
Ergodox Infinity (including #13481).
* added support for inverting the hand pin for split keyboards
* Added docs about SPLIT_HAND_LOW_IS_LEFT
* Update docs/feature_split_keyboard.md
bring #define for split hand pin low for left half name in line with grid pin define
Co-authored-by: Joel Challis <git@zvecr.com>
* Update quantum/split_common/split_util.c
update split hand pin low is left name to match split hand grid define
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Avoid zero or overflow from user's rgb_matrix_config.speed
* Avoid zero tick for reactive splash.
* Avoid zero time for animation runner.
Co-authored-by: filterpaper <filterpaper@localhost>
* Extensible split data sync capability through transactions.
- Split common transport has been split up between the transport layer
and data layer.
- Split "transactions" model used, with convergence between I2C and
serial data definitions.
- Slave matrix "generation count" is used to determine if the full slave
matrix needs to be retrieved.
- Encoders get the same "generation count" treatment.
- All other blocks of data are synchronised when a change is detected.
- All transmissions have a globally-configurable deadline before a
transmission is forced (`FORCED_SYNC_THROTTLE_MS`, default 100ms).
- Added atomicity for all core-synced data, preventing partial updates
- Added retries to AVR i2c_master's i2c_start, to minimise the number of
failed transactions when interrupts are disabled on the slave due to
atomicity checks.
- Some keyboards have had slight modifications made in order to ensure
that they still build due to firmware size restrictions.
* Fixup LED_MATRIX compile.
* Parameterise ERROR_DISCONNECT_COUNT.
* Intended usage is data validation in split transport code.
* Default space efficient algorithm.
* Opt-in fast table based algorithmn with #define CRC8_USE_TABLE switch.
* Define switches for size and speed optimized versions, the default is size
optimized by using uint_least8_t as datatype for calculations.
* #define CRC8_OPTIMIZE_SPEED uses uint_fast8_t as datatype for
calculations, this only affects 32-bit Archs like ARM and RISC-V.
* Placeholder crc_init() function for hardware backed crc calculation,
not implemented yet.
* Set saturation limit to jellybean_raindrops_anim.h
* Use faster bit-shift maths and qadd8
* Remove extra parenthesis
* Single bitmask operation is sufficient.
Co-authored-by: filterpaper <filterpaper@localhost>
* Enable SPI1 for GMMK pro
* Setup initial boilerplate for new LED driver
* RGB matrix minimally functional
* Map full LED matrix
* Return keymap to default
* Fix printscreen LED mapping
* Reduce max brightness
* Default values for AW20216
* Add documentation for AW20216
* Disable console and warnings
* Run cformat
* Update drivers/awinic/aw20216.h
Co-authored-by: Drashna Jaelre <drashna@live.com>
* make aw struct match issi struct
Co-authored-by: Drashna Jaelre <drashna@live.com>
* add led location defines
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Use led pin definitions in keyboard.c
* Add driver indices to led map
* Fix elif typo
* Run cformat
* Update docs
* Fix typo in docs
* Document global brightness limits
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Add fast_timer_t that is 16-bit or 32-bit based on architecture
A 16-bit timer will overflow sooner but be faster to compare on AVR.
* Avoid 8-bit timer overflows in debounce algorithms
Count down remaining elapsed time instead of trying to do 8-bit timer
comparisons.
Add a "none" implementation that is automatically used if DEBOUNCE is
0 otherwise it will break the _pk/_pr count down.
* Avoid unnecessary polling of the entire matrix in sym_eager_pk
The matrix only needs to be updated when a debounce timer expires.
* Avoid unnecessary polling of the entire matrix in sym_eager_pr
The matrix only needs to be updated when a debounce timer expires.
The use of the "needed_update" variable is trying to do what
"matrix_need_update" was added to fix but didn't work because it only
applied when all keys finished debouncing.
* Fix sym_defer_g timing inconsistency compared to other debounce algorithms
DEBOUNCE=5 should process the key after 5ms, not 6ms
* Add debounce tests
* Use memcmp to determine if matrix changed.
* Firmware size issues.
* Add documentation for the lack of need of MATRIX_ROW_PINS/MATRIX_COL_PINS, when overriding low-level matrix functions.
* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
Co-authored-by: Nick Brassel <nick@tzarc.org>
Tap dance callbacks may register weak mods; one case when it happens
is when a tap dance registers a key with modifiers. When the tap
dance is interrupted by pressing another key, these weak mods could
affect the interrupting key (normally any stale weak mods are cleared
at the start of action_exec() when handling a keypress event, but the
tap dance interrupt check code is called later, and the weak mods left
by that code were not cleared). Add another clear_weak_mods() call to
preprocess_tap_dance() to make sure that the interrupting keypress is
not affected by unrelated weak mods from the previous tap dance.
Fixes#12445.
The dac_basic driver did not work properly with `#define AUDIO_PIN A4`
(instead of configuring the A4 pin, the driver actually was switching
the A5 pin to analog mode, breaking any other usage of that pin in
addition to emitting a distorted signal on the improperly configured
A4 pin). Fix the code to configure the A4 pin as intended.
* Fix keycode mappings for via and ensure they don't change within protocol
* Update keycodes
* Fix broken keyboards
* added the missing keycodes found in via
* Remove invalid keycodes
Co-authored-by: David Hoelscher <infinityis@users.noreply.github.com>
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commits bundles the changes from the arm-dac-work branch focused on audio/audio_arm.* into one commit (leaving out the test-keyboard)
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
-> only the changes on audio_arm_.*, the keyboard related parts are split off to a separate commit
bfe468ef1 start morphing wavetable
474d100b5 refined a bit
208bee10f play_notes working
3e6478b0b start in-place documentation of dac settings
3e1826a33 fixed blip (rounding error), other waves, added key selection (left/right)
73853d651 5 voices at 44.1khz
dfb401b95 limit voices to working number
9632b3379 configuration for the ez
6241f3f3b notes working in a new way
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
changes by Jack Humbert on an implementation for DAC audio on arm/chibios platforms
this commit splits off the plank example keymap from commit
f52faeb5d (origin/arm-dac-work) add sample and wavetable examples, parsers for both
* refactoring: rename audio_ to reflect their supported hardware-platform and audio-generation method: avr vs arm, and pwm vs dac
* refactoring: deducplicate ISR code to update the pwm duty-cycle and period in the avr-pwm-implementation
pulls three copies of the same code into one function
which should improve readability and maintainability :-)
* refactoring: move common code of arm and avr implementation into a separate/new file
* refactoring: audio_avr_pwm, renaming defines to decouple them from actually used timers, registers and ISRs
* refactoring: audio_avr_pwm - replacing function defines with plain register defines
aligns better with other existing qmk code (and the new audio_arm_pwm) doing similar pwm thing
* add audio-arm-pwm
since not all STM32 have a DAC onboard (STM32F2xx and STM32F3xx), pwm-audio is an alternative (STM32F1xx)
this code works on a "BluePill" clone, with an STM32F103C8B
* clang-format changes on quantum/audio/* only
* audio_arm_dac: stopping the notes caused screeching when using the DAC audio paths
* audio_arm_pwm: use pushpull on the pin; so that a piezzo can be hooked up direclty without additional components (opendrain would require an external pullup)
* refactoring: remove unused file from/for atmel-avr chips
* refactoring: remove unused (avr) wavetable file
* audio_arm_dac: adapt dac_end callback to changed chibios DAC api
the previous chibios (17.6.0) passed along a pointer into the buffer plus a sample_count (which are/already where included in the DACDrivre object) - the current chibios (19.1.0) only passes the driver object.
this patch ports more or less exactly what the previous chibios ISR code did: either have the user-callback work the first or second half of the buffer (dacsample_t pointer, with half the DAC_BUFFER_SIZE samples) by adjusting the pointer and sample count
* audio-arm-dac: show a compile-warning on undefined audio-pins
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio_arm_dac: switch from exemplary wavetable generation to sine only
sine+triangle+squrare is exemplary, and not realy fit for "production" use
'stairs' are usefull for debugging (hardware, with an oscilloscope)
* audio_arm_dac: enable output buffers in the STM32
to drive external loads without any additional ciruitry - external opamps and such
* audio: prevent out-of-bounds array access
* audio_arm_dac: add output-frequency correcting factor
* audio_arm_pwm: get both the alternate-function and pm-callback variants back into working condition
and do some code-cleanup, refine documentation, ...
* audio_arm_pwm: increase pwm frequency for "higher fidelity"
on the previous .frequency=100000 higher frequency musical notes came out wrong
(frequency measured on a Tektronix TDS2014B)
note | freq | arm-pwm
C2 | 65.4 | 65.491
C5 | 523.25 | 523.93
C6 | 1046.5 | 1053.38
C7 | 2093 | 2129
C8 | 4186 | 4350.91
with .frequency = 500000
C8 | 4186 | 4204.6
* audio refactoring: remove unused variables
* audio_arm_dac: calibrate note tempo: with a tempo of 60beats-per-second a whole-note should last for exactly one second
* audio: allow feature selection in rules.mk
so the user can switch the audio driver between DAC and PWM on STM32 boards which support both (STM32F2 and up)
or select the "pin alternate" pwm mode, for example on STM32F103
* audio-refactoring: move codeblocks in audio.[ch] into more coherent groups
and add some inline documentation
* audio-refactoring: cleanup and streamline common code between audio_arm_[dac|pwm]
untangeling the relation between audio.c and the two drivers
and adding more documenting comments :-)
* audio_avr_pwm: getting it back into working condition, and cleanup+refactor
* audio-refactoring: documentation and typo fixes
Co-Authored-By: Nick Brassel <nick@tzarc.org>
* audio-refactoring: cleanup defines, inludes and remove debug-prints
* audio_chibios_dac: define&use a minimal sampling rate, based on the available tone-range
to ease up on the cpu-load, while still rendering the higher notes/tones sufficiently
also reenable the lower tones, since with the new implementation there is no evidence of them still beeing 'bugged'
* audio-refactoring: one common AUDIO_MAX_VOICES define for all audio-drivers
* audio-chibios-pwm: pwm-pin-allternate: make the the timer, timer-channel and alternate function user-#definable
* audio_chibios_dac: math.h has fmod for this
* Redo Arm DAC implementation for additive, wavetable synthesis, sample playback
update Jack Humberts dac-example keymaps for the slight changes in the audio-dac interface
* audio-refactoring: use a common AUDIO_PIN configuration switch instead of defines
have the user select a pin by configuration in rules.mk instead of a define in config.h
has the advantage of beeing in a common form/pattern across all audio-driver implementations
* audio-refactoring: switch backlight_avr.c to the new AUDIO_PIN defines
* audio-common: have advance_note return a boolean if the note changed, to the next one in the melody beeing played
* audio-chibios-pwm: fix issue with ~130ms silence between note/frequency changes while playing a SONG
through trial,error and a scope/logic analyzer figured out Chibios-PWMDriver (at least in the current version) misbehaves if the initial period is set to zero (or one; two seems to work); when thats the case subsequent calls to 'pwmChhangePeriod' + pwmEnableChannel took ~135ms of silence, before the PWM continued with the new frequency...
* audio-refactoring: get 'play_note' working again
with a limited number of available voices (say AUDIO_VOICES_MAX=1) allow new frequencies to be played, by discarding the oldest one in the 'frequencies' queue
* audio: set the fallback driver to DAC for chibios and PWM for all others (==avr at the moment)
* audio-refactoring: moore documentation
and some cleanup
* audio-avr-pwm: no fallback on unset AUDIO_PIN
this seems to be the expected behaviour by some keyboards (looking at ckeys/handwire_101:default) which otherwise fail to build because the firmware-image ends up beeing too large for the atmega... so we fail silently instead to keep travis happy
* audio-refactoring: untangling terminology: voice->tone
the code actually was working on tones (combination of pitch/frequency, duration, timbre, intensity/volume) and not voices (characteristic sound of an instrument; think piano vs guitar, which can be played together, each having its own "track" = voice on a music sheet)
* audio-pwm: allow freq=0 aka a pause/rest in a SONG
continue processing, but do not enable pwm units, since freq=0 wouldn't produce any sound anyway (and lead to division by zero on that occasion)
* audio-refactoring: audio_advance_note -> audio_advance_state
since it does not only affect 'one note', but the internally kept state as a whole
* audio-refactoring: untangling terminology: polyphony
the feature om the "inherited" avr code has little to do with polyphony (see wikipedia), but is more a time-multiplexing feature, to work around hardware limitations - like only having one pwm channel, that could on its own only reproduce one voice/instrument at a time
* audio-chibios-dac: add zero-crossing feature
have tones only change/stop when the waveform approaches zero - to avoid audible clicks
note that this also requires the samples to start at zero, since the internally kept index into the samples is reset to zero too
* audio-refactoring: feature: time-multiplexing of tones on a single output channel
this feature was in the original avr-pwm implementation misnomed as "polyphony"
with polyphony_rate and so on; did the same thing though: time-multiplexing multiple active notes so that a single output channel could reproduce more than one note at a time (which is not the same as a polyphony - see wikipedia :-) )
* audio-avr-pwm: get music-mode working (again) on AVRs
with both pwm channels, or either one of the two :-)
play_notes worked already - but music_mode uses play_note
* audio-refactoring: split define MAX_SIMULTANEOUS_TONES -> TONE_STACKSIZE
since the two cases are independant from one another, the hardware might impose limitations on the number of simultaneously reproducable tones, but the audio state should be able to track an unrelated number of notes recently started by play_note
* audio-arm-dac: per define selectable sample-luts
plus generation script in ./util
* audio-refactoring: heh, avr has a MIN...
* audio-refactoring: add basic dac audio-driver based on the current/master implementation
whereas current=d96380e65496912e0f68e6531565f4b45efd1623
which is the state of things before this whole audio-refactoring branch
boiled down to interface with the refactored audio system = removing all
redundant state-managing and frequency calculation
* audio-refactoring: rename audio-drivers to driver_$PLATFORM_$DRIVER
* audio-arm-pwm: split the software/hardware implementations into separate files
which saves us partially from a 'define hell', with the tradeoff that now two somewhat similar chibios_pwm implementations have to be maintained
* audio-refactoring: update documentation
* audio-arm-dac: apply AUDIO_PIN defines to driver_chibios_dac_basic
* audio-arm-dac: dac_additive: stop the hardware when the last sample completed
the audio system calls for a driver_stop, which is delayed until the current sample conversion finishes
* audio-refactoring: make function-namespace consistent
- all (public) audio functions start with audio_
- also refactoring play*_notes/tones to play*_melody, to visually distance it a bit from play*_tone/_note
* audio-refactoring: consistent define namespace: DAC_ -> AUDIO_DAC_
* audio-arm-dac: update (inline) documentation regarding MAX for sample values
* audio-chibios-dac: remove zero-crossing feature
didn't quite work as intended anyway, and stopping the hardware on close-to-zero seems to be enought anyway
* audio-arm-dac: dac_basic: respect the configured sample-rate
* audio-arm-pwm: have 'note_timbre' influence the pwm-duty cycle
like it already does in the avr implementation
* audio-refactoring: get VIBRATO working (again)
with all drivers (verified with chibios_[dac|pwm])
* audio-arm-dac: zero-crossing feature (Mk II)
wait for the generated waveform to approach 'zero' before either turning off the output+timer or switching to the current set of active_tones
* audio-refactoring: re-add note-resting -> introduce short_rest inbetween
- introduce a short pause/rest between two notes of the same frequency, to separate them audibly
- also updating the refactoring comments
* audio-refactoring: cleanup refactoring remnants
remove the former avr-isr code block - since all its features are now refactored into the different parts of the current system
also updates the TODOS
* audio-refactoring: reserve negative numbers as unitialized frequencies
to allow the valid tone/frequency f=0Hz == rest/pause
* audio-refactoring: FIX: first note of melody was missing
the first note was missing because 'goto_next_note'=false overrode a state_change=true of the initial play_tone
and some code-indentations/cleanup of related parts
* audio-arm-dac: fix hardware init-click
due to wron .init= value
* audio-refactoring: new conveniance function: audio_play_click
which can be used to further refactor/remove fauxclicky (avr only) and/or the 'clicky' features
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: consecutive notes of the same frequency get a pause inserted inbetween by audio.c
* audio-refactoring: use milliseconds instead of seconds for 'click' parameters
clicks are supposed to be short, seconds make little sense
* audio-refactoring: use timer ticks instead of counters
local counters were used in the original (avr)ISR to advance an index into the lookup tables (for vibrato), and something similar was used for the tone-multiplexing feature
decoupling these from the (possibly irregular) calls to advance_state made sesne, since those counters/lookups need to be in relation to a wall-time anyway
* audio-refactoring: voices.c: drop 'envelope_index' counter in favour of timer ticks
* audio-refactoring: move vibrato and timbre related parts from audio.c to voices.c
also drops the now (globally) unused AUDIO_VIBRATO/AUDIO_ENABLE_VIBRATO defines
* audio.c: use system-ticks instead of counters the drivers have to take care of for the internal state posision
since there already is a system-tick with ms resolution, keeping count separatly with each driver implementation makes little sense; especially since they had to take special care to call audio_advance_state with the correct step/end parameters for the audio state to advance regularly and with the correct pace
* audio.c: stop notes after new ones have been started
avoids brief states of with no notes playing that would otherwise stop the hardware and might lead to clicks
* audio.c: bugfix: actually play a pause
instead of just idling/stopping which lead the pwm drivers to stop entirely...
* audio-arm-pwm: pwm-software: add inverted output
new define AUDIO_PIN_ALT_AS_NEGATIVE will generate an inverted signal on the alternate pin, which boosts the volume if a piezo is connected to both AUDIO_PIN and AUDIO_PIN_ALT
* audio-arm-dac: basic: handle piezo configured&wired to both audio pins
* audio-refactoring: docs: update for AUDIO_PIN_ALT_AS_NEGATIVE and piezo wiring
* audio.c: bugfix: use timer_elapsed32 instad of keeping timestamps
avoids running into issues when the uint32 of the timer overflows
* audio-refactoring: add 'pragma once' and remove deprecated NOTE_REST
* audio_arm_dac: basic: add missing bracket
* audio.c: fix delta calculation
was in the wrong place, needs to use the 'last_timestamp' before it was reset
* audio-refactoring: buildfix: wrong legacy macro for set_timbre
* audio.c: 16bit timerstamps suffice
* audio-refactoring: separate includes for AVR and chibios
* audio-refactoring: timbre: use uint8 instead of float
* audio-refactoring: duration: use uint16 for internal per-tone/note state
* audio-refactoring: tonemultiplexing: use uint16 instead of float
* audio-arm-dac: additive: set second pin output-low
used when a piezo is connected to AUDIO_PIN and AUDIO_PIN_ALT, with PIN_ALT_AS_NEGATIVE
* audio-refactoring: move AUDIO_PIN selection from rules.mk to config.h
to be consistent with how other features are handled in QMK
* audio-refactoring: buildfix: wrong legacy macro for set_tempo
* audio-arm-dac: additive: set second pin output-low -- FIXUP
* audio.c: do duration<>ms conversion in uint instead of float
on AVR, to save a couple of bytes in the firmware size
* audio-refactoring: cleanup eeprom defines/usage
for ARM, avr is handled automagically through the avr libc and common_features.mk
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* audio.h: throw an error if OFF is larger than MAX
* audio-arm-dac: basic: actually stop the dac-conversion on a audio_driver_stop
to put the output pin in a known state == AUDIO_DAC_OFF_VALUE, instead of just leaving them where the last conversion was... with AUDIO_PIN_ALT_AS_NEGATIVE this meant one output was left HIGH while the other was left LOW
one CAVEAT: due to this change the opposing squarewave when using both A4 and A5 with AUDIO_PIN_ALT_AS_NEGATIVE
show extra pulses at the beginning/end on one of the outputs, the two waveforms are in sync otherwise.
the extra pusles probably matter little, since this is no high-fidelity sound generation :P
* audio-arm-dac: additive: move zero-crossing code out of dac_value_generate
which is/should be user-overridable == simple, and doing one thing: providing sample values
state-transitions necessary for the zero crossing are better handled in the surrounding loop in the dac_end callback
* audio-arm-dac: dac-additive: zero-crossing: ramping up or down
after a start trigger ramp up: generate values until zero=OFF_VALUE is reached, then continue normally
same in reverse for strop trigger: output values until zero is reached/crossed, then keep OFF_VALUE on the output
* audio-arm-dac: dac-additive: BUGFIX: return OFF_VALUE when a pause is playing
fixes a bug during SONG playback, which suddenly stopped when it encoutnered a pause
* audio-arm-dac: set a sensible default for AUDIO_DAC_VALUE_OFF
1/2 MAX was probably exemplary, can't think of a setup where that would make sense :-P
* audio-arm-dac: update synth_sample/_wavetable for new pin-defines
* audio-arm-dac: default for AUDIO_DAC_VALUE_OFF
turned out that zero or max are bad default choices:
when multiple tones are played (>>5) and released at the same time (!), due to the complex waveform never reaching 'zero' the output can take quite a while to reach zero, and hence the zero-crossing code only "releases" the output waaay to late
* audio-arm-dac: additive: use DAC for negative pin
instead of PAL, which only allows the pin to be configured as output; LOW or HIGH
* audio-arm-dac: more compile-time configuration checks
* audio-refactoring: typo fixed
* audio-refactoring: clang-format on quantum/audio/*
* audio-avr-pwm: add defines for B-pin as primary/only speaker
also updates documentation.
* audio-refactoring: update documentation with proton-c config.h example
* audio-refactoring: move glissando (TODO) to voices.c
refactored/saved from the original glissando implementation in then upstream-master:audio_avr.c
still needs some work though, as it is now the calculation *should* work, but the start-frequency needs to be tracked somewhere/somehow; not only during a SONG playback but also with user input?
* audio-refactoring: cleanup: one round of aspell -c
* audio-avr-pwm: back to AUDIO_PIN
since config_common.h expands them to plain integers, the AUDIO_PIN define can directly be compared to e.g. B5
so there is no need to deal with separate defines like AUDIO_PIN_B5
* audio-refactoring: add technical documentation audio_driver.md
which moves some in-code documentation there
* audio-arm-dac: move AUDIO_PIN checks into c-code
instead of doing everything with the preprocessor, since A4/A5 do not expand to simple integers, preprocessor int-comparison is not possible. but necessary to get a consistent configuration scheme going throughout the audio-code... solution: let c-code handle the different AUDIO_PIN configurations instead (and leave code/size optimizations to the compiler)
* audio-arm-dac: compile-fix: set AUDIO_PIN if unset
workaround to get the build going again, and be backwarts compatible to arm-keyboards which not yet set the AUDIO_PIN define. until the define is enforced through an '#error"
* audio-refactoring: document tone-multiplexing feature
* audio-refactoring: Apply suggestions from documentation review
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-refactoring: Update docs/audio_driver.md
* audio-refactoring: docs: fix markdown newlines
Terminating a line in Markdown with <space>-<space>-<linebreak> creates an HTML single-line break (<br>).
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* audio-arm-dac: additive: fix AUDIO_PIN_ALT handling
* audio-arm-pwm: align define naming with other drivers
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-refactoring: set detault tempo to 120
and add documentation for the override
* audio-refactoring: update backlight define checks to new AUDIO_PIN names
* audio-refactoring: reworking PWM related defines
to be more consistent with other QMK code
Co-authored-by: Joel Challis <git@zvecr.com>
* audio-arm: have the state-update-timer user configurable
defaulting to GPTD6 or GPTD8 for stm32f2+ (=proton-c)
stm32f1 might need to set this to GPTD4, since 6 and 8 are not available
* audio-refactoring: PLAY_NOTE_ARRAY was already removed in master
* Add prototype for startup
* Update chibiOS dac basic to disable pins on stop
* Add defaults for Proton C
* avoid hanging audio if note is completely missed
* Don't redefine pins if they're already defined
* Define A4 and A5 for CTPC support
* Add license headers to keymap files
* Remove figlet? comments
* Add DAC config to audio driver docs
* Apply suggestions from code review
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Add license header to py files
* correct license header
* Add JohSchneider's name to modified files
AKA credit where credit's due
* Set executable permission and change interpeter
* Add 'wave' to pip requirements
* Improve documentation
* Add some settings I missed
* Strip AUDIO_DRIVER to parse the name correctly
* fix depreciated
* Update util/audio_generate_dac_lut.py
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* Fix type in clueboard config
* Apply suggestions from tzarc
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Johannes <you@example.com>
Co-authored-by: JohSchneider <JohSchneider@googlemail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joshua Diamond <josh@windowoffire.com>
Co-authored-by: Jack Humbert <jack.humb@gmail.com>
* LED Matrix: add led_matrix_types.h and implement g_led_config
* Set correct flags for non-"modifier" LEDs
* Clean up docs a little
* Add license headers for [led,rgb]_matrix_types.h
* Improve Pointing Device report sending
* Hide old report behind preprocessors too
* put host_mouse_send() in curly brackets
* Remove POINTING_DEVICE_ALWAYS_SEND_REPORT functionality
* Fix typo
* fix function ref in docs
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* at90usb162 support
* fix missing bracket
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
With MAJOR_MODE (= major scale), keys in one octave is not 12 but 7.
To solve this problem, change divisor number from 12 to 7 at %(Modulo) and /(Division).
NOTE:
The last 12 represents half step keys in one octave for pitch calculation.
* add byte order bgr for ws2812
* update docs for driver change
* Update ws2812_driver.md
* Update docs/ws2812_driver.md
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* fix matrix_io_delay() timing in quantum/matrix.c
* Updated comments explaining the need for matrix_io_delay() in quantum/matrix.c
* fix matrix_io_delay() timing in quantum/split_common/matrix.c
* Update quantum/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/split_common/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/split_common/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* add waitOutputPinValid() and wait_cpuclock() into quantum/quantum.h and tmk_core/common/wait.h
* add matrix_output_select_delay() and matrix_output_unselect_delay()
* fix quantum/matrix_common.c, tmk_core/common/matrix.h
* fix tmk_core/common/wait.h
* fix quantum/quantum.h, tmk_core/common/wait.h
* waitOutputPinValid() rename to waitInputPinDelay() in quantum/quantum.h.
* waitOutputPinValid() rename to waitInputPinDelay() in quantum/matrix_common.c
* update tmk_core/common/wait.h
* update comment in quantum/matrix.c, quantum/split_common/matrix.c
* update quantum/quantum.h: Make more margin in the GPIO_INPUT_PIN_DELAY default value.
Co-authored-by: Ryan <fauxpark@gmail.com>
* Allow recording of the last matrix activity time, to simplify implementation of display timeouts and the like.
* Add requested changes from code review.
* Simplify split matrix last changed.
* Add proper prototypes for Tap-Hold Per Key functions
* Fix handwired/tennie default keymap
* Remove unneeded references
* Fix tapping term per key check in space cadet
* Pre-emptive fix for tap dance
* Fix marksard/leftover30
* Replace hard coded tapping term with define
* Added mac variant of portuguese keymap
This keymap is very similar to the existing portuguese keymap, but
some symbols are moved around.
Apply suggestions from code review
Corrected whitespace and implemented some suggested changes.
Co-authored-by: Ryan <fauxpark@gmail.com>
Converted some spaces to nbsp
Added sendstring ISO version
* Apply suggestions from code review
Added suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* Replaced space with nbsp
* Corrected 2 chars in ascii_to_shift_lut
{ and } require shift
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add modifier state to the split transport
This adds modifier state to the i2c and serial transport for split
keyboards. The purpose of this is to allow e.g. displaying modifier
state on the slave side of a split keyboard on an oled. This adds one
byte to the data transferred between halves.
This also fixes a missing ifdef guard for BLACKLIGHT_ENABLE.
Break modifiers into real/weak/oneshot
Fix incorrect slave serial mod setting
Fix typo in serial weal mod setter
Fix build errors for the I2C code that I introduced
Code cleanup and formatting per project preferences
Correctly get oneshot mods
Fix missing braces
Remove unneeded ifdef guard
Make the added state transport optional
Add documentation for the new define to enable this feature
Fix stray grave mark
* Fix error introduced in conflict resolution
When `rgblight.c` includes `rgblight_breathe_table.h`, the search order should be as follows.
* `keyboards/KEYBOARD/keymaps/USER/rgblight_breathe_table.h`
* `users/USER/rgblight_breathe_table.h`
* `quantum/rgblight_breathe_table.h`
However, the current implementation was wrong, so I fixed it.
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* Recommend use of LED Indicator config
* Recommend use of LED Indicator config - update link
* Update quantum/template/ps2avrgb/config.h
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* First pass
* Add config options to docs
* Update some wording
* Slight tidy up of backlight caps logic
* Init pin to correct state
* Move init location
* Reverse default state
* quantum/debounce: rename debouncing algorithms according to Issue 8763
This is the second attempt at implementation, with no ts_ and cy_ prefixes, since those will be implemented with macros.
* Debouncing documentation: Refactor, add some generic info, and merge into a single document
* Fixed Spanish keymap extra ES_DIAE symbol
`ES_DIAE` should be `S(ES_ACUT)` not `S(ES_GRV)`
* Update quantum/keymap_extras/keymap_spanish.h
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* K-Type refactor
* Declare QMK in product name again
* Hopefully fix matrix scanning
* Maybe this time
* Partial (literally) RGB Matrix support
* Put RGB_MATRIX_ENABLE into rgb keymap for now
* Add ifdefs for RGB config
* Set layer 1 to actually be layer 1...
* Update keyboards/k_type/readme.md
* Put all RGB config in keymap for now
* Set SDB high?
* Before `rgb_matrix_init()` would be best
* User level, not keyboard
* Combating dropped keys
* Nope
* Readme for RGB keymap
* Remove custom matrix
* Add support for hsv->rgb conversion without using CIE curve.
* Modify anavi/macropad8 to disable unicode (was unused), otherwise firmware size is too large.
* Consolidate TKC projects and increase VIA keymap count to 4.
* Updated readme files.
* Removed config.h via limitation of 2 dynamic keymaps
* Reduce dynamic keymaps from 4 to 3 due to EEPROM space limitations.
* Update dynamic_keymap.c
* Restore 4 dynamic keymaps for VIA in TKC projects.
* Update quantum/dynamic_keymap.c
* Tweak the Christmas animation effect to be less harsh on the eyes
* Further improve the tweaked Christmas animation code
- Use constants where it makes sense
- Instead of complicated math, use a static variable to keep track if it's animating from or to red
- Don't use pow (but a simple macro instead)
- Using floating point math is necessary for the fraction in the cubic bezier function to work
* Update docs for the tweaked Christmas animation effect
* Further improve memory usage
- Don't use floats, but 32 bit ints instead (where needed)
- Replace limits.h with constant
* Fix typo
* add support for hid gamepad interface
add documentation for HID joystick
Add joystick_task to read analog axes values even when no key is pressed or release. update doc
Update docs/feature_joystick.md
Manage pin setup and read to maintain matrix scan after analog read
* Incorporates patches and changes to HID reporting
There are some patches provided by @a-chol incorporated on this commit,
and also some changes I made to the HID Report structure.
The most interesting is the one dealing with number of buttons: Linux
doesn't seem to care, but Windows requires the HID structure to be byte
aligned (that's in the spec). So if one declares 8/16/32... buttons they
should not have any issues, but this is what happens when you have 9
buttons:
```
bits |0|1|2|3|4|5|6|7|
|*|*|*|*|*|*|*|*| axis 0 (report size 8)
|*|*|*|*|*|*|*|*| ...
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*| axis 6
|*|*|*|*|*|*|*|*| first 8 buttons (report size 1)
|*| | | | | | | | last of 9 buttons, not aligned
```
So for that I added a conditonal that will add a number of reports with
size 1 to make sure it aligns to the next multiple of 8. Those reports
send dummy inputs that don't do anything aside from aligning the data.
Tested on Linux, Windows 10 and Street Fighter (where the joystick is
recognized as direct-input)
* Add save and restore of each pin used in reading joystick (AVR).
Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc
instead of an output pin from the MCU.
Fix joystick report id
Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes)
Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis.
Documentation fixes
* Fix port addressing for joystick analog read
* The other required set of changes
As per the PR, the changes still holding it up.
Add onekey for testing.
Fix ARM builds.
Fix device descriptor when either axes or buttons is zero.
Add compile-time check for at least one axis or button.
Move definition to try to fix conflict.
PR review comments.
qmk cformat
* avoid float functions to compute range mapping for axis adc reading
* Remove V-USB support for now. Updated docs accordingly.
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios
* Fix HID joystick report sending for ChibiOS.
Add one analog axis to the onekey:joystick keymap.
Fix pin state save and restore during joystick analog read for STM32
MCUs.
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add missing mcuconf.h and halconf.h to onekey:joystick keymap.
Add suggested fixes from PR.
* Switch saveState and restoreState signature to use pin_t type.
onekey:joystick : add a second axis, virtual and programmatically animated.
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add PR corrections
* Remove halconf.h and mcuconf.h from onekey keymaps
* Change ADC_PIN to A0
Co-authored-by: achol <allecooll@hotmail.com>
Co-authored-by: José Júnior <jose.junior@gmail.com>
Co-authored-by: a-chol <achol@notamail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update Space Cadet to use Custom Tapping Term functionality
* Detect correct keycode for space cadet tapping term
* Update tap dancing to use global custom tapping term
* Update documentation for Tap Dances
* formatting pass
* Apply suggestions from code review
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update docs/feature_tap_dance.md
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Update for future
* Update user keymaps for space cadet
* Fix typos
* Clean up tapping term stuff
* Fix compiler issue if NO_ACTION_TAPPING is enabled
Co-authored-by: fauxpark <fauxpark@gmail.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Initial work for consolidation of board files and default ChibiOS configs.
* Migrate F401/F411 black pills for testing.
* Add early init bootloader jump flag.
* Add support for I2C in order to use i2c_scanner keymap.
* Add F401/F411 HSE bypass to get things booting.
* Exempt "hooked" ChibiOS conf files from updater script.
* Fix up ordering for bootloader_defs file check.
* Match previous $(KEYBOARD_PATHS) value for Proton-C, updated for all board configs.
Specifically, when rgb matrix is enabled and using the ws2812 driver, and rgb light is enabled at the same time, print a message about coexistance because it can cause issues, since you cannot change pins/config for the WS2812 driver.
* Issue 9942: Add Quantum defines
Add codes to quantum_keycodes for LSA, RSA, RCS, and their corresponding _T macros
* 9942: Add documentation for new defines
Add documentation for new defines in feature request 9942. Also define SAGR and SAGR_T as aliases for RSA and RSA_T.
* Update quantum/quantum_keycodes.h
* Update docs/keycodes.md
* Update docs/keycodes.md
* Update docs/keycodes.md
* Update docs/keycodes.md
* Add Indicator flag for RGB Matrix
This adds a new flag for the RGB Matrix feature that lets you specify if the LED is an indicator LED, to be used to indicate the system state of the keyboard (eg caps/num/etc lock status, layer indication, modifer status, etc).
* Better formatting of table
* Add IS_LAYER_ON_STATE()/IS_LAYER_OFF_STATE() macros
* Add docs for IS_LAYER_ON/OFF(_STATE) macros
* Remove IS_LAYER_ON/OFF_STATE redefinition in userspace
* Run clang-format on quantum/quantum.h
* Redefine IS_LAYER_ON/OFF(_STATE) as aliases of existing layer functions
Also update relevant doc entries.
Needs testing to check if this breaks existing IS_LAYER_ON/OFF usage in certain
edge cases (namely calling the macros with 0).
* Reformat layer check function docs
* dipsw test on helix/rev2/sc/back:five_rows
* add peek_matrix() to matrix_common.c
* add DIP_SWITCH_MATRIX_GRID support to quantum/dip_switch.c
* update docs/feature_dip_switch.md about DIP_SWITCH_MATRIX_GRID
* Test end. remove test code. Revert "dipsw test on helix/rev2/sc/back:five_rows"
This reverts commit 6d4304c74557597c9fb4d324f79c3ae4793ae874.
* Add Hebrew keymap aliases
* Use NBSP for internal space in box drawings
* Apply suggestions from code review
* More whitespace fixes
* IL_DVAV, IL_DYOD and IL_VYOD were incorrect
* Add IL_DEG, IL_MUL, IL_DIV
* Hebrew is now ISO (no more BAE)
* Use ISO left shift
* Apply suggestions from code review
* DYOD and VYOD were reversed in diagram.
Oops!
* Change `led` to `led_matrix` in rgb_matrix_drivers
Is a minor change that only affects the driver file.
However, this will allow somebody to run rgblight along side rgb matrix
using the ws2812 driver, as well. Specifically, so you can use the
custom driver for rgblight to set a different pin (barring a change to
the `ws2812_setleds` function).
Courtesy of discord conversion:
https://discordapp.com/channels/440868230475677696/568161140534935572/721555623191248906
* Change name to be super specific
* Update rgb_matrix_drivers.c
* Fixed slave-side keyboard half unresponsiveness
due to how LUFA handles USB_Disable()
* changes to formatting
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Branch point for 2020 May 30 Breaking Change
* Migrate `ACTION_LAYER_TOGGLE` to `TG()` (#8954)
* Migrate `ACTION_MODS_ONESHOT` to `OSM()` (#8957)
* Migrate `ACTION_DEFAULT_LAYER_SET` to `DF()` (#8958)
* Migrate `ACTION_LAYER_MODS` to `LM()` (#8959)
* Migrate `ACTION_MODS_TAP_KEY` to `MT()` (#8968)
* Convert V-USB usbdrv to a submodule (#8321)
* Unify Tap Hold functions and documentation (#8348)
* Changing board names to prevent confusion (#8412)
* Move the Keyboardio Model01 to a keyboardio/ subdir (#8499)
* Move spaceman keyboards (#8830)
* Migrate miscellaneous `fn_actions` entries (#8977)
* Migrate `ACTION_MODS_KEY` to chained mod keycodes (#8979)
* Organizing my keyboards (plaid, tartan, ergoinu) (#8537)
* Refactor Lily58 to use split_common (#6260)
* Refactor zinc to use split_common (#7114)
* Add a message if bin/qmk doesn't work (#9000)
* Fix conflicting types for 'tfp_printf' (#8269)
* Fixed RGB_DISABLE_AFTER_TIMEOUT to be seconds based & small internals cleanup (#6480)
* Refactor and updates to TKC1800 code (#8472)
* Switch to qmk forks for everything (#9019)
* audio refactor: replace deprecated PLAY_NOTE_ARRAY (#8484)
* Audio enable corrections (2/3) (#8903)
* Split HHKB to ANSI and JP layouts and Add VIA support for each (#8582)
* Audio enable corrections (Part 4) (#8974)
* Fix typo from PR7114 (#9171)
* Augment future branch Changelogs (#8978)
* Revert "Branch point for 2020 May 30 Breaking Change"
This commits add the SH_OS keycode, which works similarly to one shot
layers:
* while pressed, the keyboard is swapped
* if no keys were pressed while it was pressed, the next key press is
swapped
SH_OS also supports chaining with one shot layers:
OSL(x) + SH_OS + key interprets the key press on the oneshot layer.
The ONESHOT_TIMEOUT setting used by one shot keys and layers is also
used by oneshot swap hands. In the above chaining scenario the timeout
of the oneshot layer is reset when swap hands is activated.
Resolves#2682
* Allow 16 lighting layers
* Require #define RGBLIGHT_LAYERS_16 to enable 16 layers
* Override RGBLIGHT_MAX_LAYERS to set maximum number of lighting layers
* Enforce lower bound on RGBLIGHT_MAX_LAYERS
Co-Authored-By: Takeshi ISHII <2170248+mtei@users.noreply.github.com>
* Fix an error in the check for valid RGBLIGHT_MAX_LAYERS
* Don't use bitfield / PACKED, as it causes bloat
* Update documentation re: up to 32 lighting layers
* Run cformat
* Add note about increasing FW size in docs/config_options.md
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Remove no-longer-valid comment
* Add doc note that split sync will be slower
Co-authored-by: Takeshi ISHII <2170248+mtei@users.noreply.github.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Implement momentarily blink of lighting layers
* Refactor spidey3 userspace to use rgb layer blink
* Remove un-necessary line from example in documentation
* Revert "Refactor spidey3 userspace to use rgb layer blink"
This reverts commit 831649bb680c41c6d663ae6fa86d13f4f8bebdd8.
* Adds a missing bit of documentation about lighting layer blink
* Update docs/feature_rgblight.md per suggestions
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Update docs/feature_rgblight.md per suggestions
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Update docs/feature_rgblight.md per suggestions
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* cformat, as suggested
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Invert UC_MOD/UC_RMOD direction when Shift is held
Also use MOD_MASK_SHIFT in process_rgb.c
* Allow audio to be played for UC_MOD, UC_RMOD keycodes as well
* Fix signedness bug in reverse input mode cycling
* Misc formatting in process_unicode_common.c
* Address clang-format issues
* Make decode_utf8 helper function file-local (static)
* Branch point for 2020 May 30 Breaking Change
* audio-configuration: template: audio_avr.c does NOT default to C6
not on its own, it needs a pin configured per define in config.h for audio to actually work
otherwise only parts of the code are included in the firmware, wasting space and possibly breaking builds because auf hitting the firmware-size limits
* audio-configuration: strip comment to bare essentials
Co-Authored-By: Ryan <fauxpark@gmail.com>
* revert future change
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Johannes <you@example.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: zvecr <git@zvecr.com>
* add 'togglePin' conveniance function
for AVR and chibios
* drop outmost parantheses
Co-Authored-By: Konstantin Đorđević <vomindoraan@gmail.com>
* toggle pin on avrs
toggle a pin configured as output by writing the corresponding bit to the PIN register
Co-Authored-By: Takeshi ISHII <2170248+mtei@users.noreply.github.com>
* togglepin: add documentation for newly added function
* Update docs/internals_gpio_control.md
Co-Authored-By: Konstantin Đorđević <vomindoraan@gmail.com>
* on AVR: use PORTD to toggle the output
... since not all MCUs support toggling through writing to PIN
Co-Authored-By: Ryan <fauxpark@gmail.com>
Co-authored-by: Johannes <you@example.com>
Co-authored-by: Konstantin Đorđević <vomindoraan@gmail.com>
Co-authored-by: Takeshi ISHII <2170248+mtei@users.noreply.github.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
QMK Bot
Joakim Tufvegren
Joel Challis
Drashna Jaelre
Nick Brassel
Patrick Stadler
Carl-Fredrik Arvidson
Ryan
Takeshi ISHII
Johannes Choo
Chris Cullin
Jonas Gessner
Jameson Thatcher
Thomas Weißschuh
Stefan Kerkmann
Albert Y
XScorpion2
Simon Arlott
Gigahawk
James Young
Erovia
Donald Kjer
Michael Stapelberg
Matthes W
Zach White
github-actions[bot]
Xelus22
Purdea Andrei
Sergey Vlasov
Daniel Rodríguez Rivero
Joshua Diamond
TurtleHunter
즈눅
jakobkg
xyzz
Dasky
Takeshi Nishio
kb-elmo
André Silva
André Cruz
Casey Webster
Hedgestock
Josh Hinnebusch
r-pufky
Sergey Omelchenko
Geoffrey BOTIN
X-Bows Tech
Félix Sanz
a_p_u_r_o
3araht
sol
cmdremily
Wilba
Olivier Li
Greg Wright
David Kosorin
Tynan Beatty
TerryMathews
Max Rumpf
a-chol
Pete Sevander
nopunin10did
BeefaloKing
Konstantin Đorđević
Hedgestock
Oskar Holstensson
Guillaume Gérard
Dongfeng Yu
Olli
MelGeek
Jason Laqua
itsnoteasy
Adrian
Kimat Boven
Zsolt Parragi
JohSchneider